MagiZinc coated steel for forming is formable and deep drawable from a reasonable quality (DX51) to a good quality (DX56).

The mechanical properties and chemical composition of MagiZinc coated steel for forming is in line with the following standards: 

European standard	National standards
	UK	Germany
EN 10327, 2004	BS 2989	DIN 17162-1
DX51D+ZMA	Z1 + Z2	St 02 Z
DX52D+ZMA	Z3	St 03 Z
DX53D+ZMA	Z5	St 05 Z
DX54D+ZMA	Z6 1)	St 06 Z
DX56D+ZMA	-	St 07 Z 1)

¹⁾ Not in standard.

MagiZinc coated steel for forming has the following mechanical properties - these are measured transverse to the rolling direction: 

	Re 1)	Rm	A80 2)	r90	n90
	Min-Max	Min-Max	Min.	Min.	Min.
Grade	N/mm²	N/mm²	%
DX51D+ZMA	-	270-500	22	-	-
DX52D+ZMA	140-300 3)	270-420	26	-	-
DX53D+ZMA	140-260	270-380	30	-	-
DX54D+ZMA	120-220	260-350	36	1.6	0.18
DX56D+ZMA	120-180	260-350	39	1.9 4)	0.21

¹⁾ The values of the yield strength are those of the 0.2% yield strength for products with no definite yield point,

    and the lower yield strength R_eL for the other products
²⁾ For a thickness t ≤ 0.7 mm the minimum elongation after fracture is decreased by 2%.
³⁾ This value only applies to skin-passed products

⁴⁾ For a thickness t > 1.5 mm the r₉₀ value is reduced by 0.2.

Heat analysis with maximum values in weight percentages: 

	C	Mn	P	S	Al	N	Ti
Grade	Max.	Max.	Max.	Max.	Min.	Max.	Max.
DX51D+ZMA	0.100	0.700	0.100	0.035	0.025	0.010	0.060
DX52D+ZMA	0.070	0.300	0.030	0.035	0.025	0.005	0.005
DX53D+ZMA	0.030	0.300	0.060	0.035	0.010	0.010	0.125
DX54D+ZMA	0.010	0.300	0.030	0.035	0.010	0.006	0.125
DX56D+ZMA	0.005	0.300	0.020	0.020	0.010	0.005	0.085

MagiZinc coated steel for forming is available in the following dimensions in mm: 

Thickness	Maximum Width
from-up to	DX51	DX52	DX53	DX54	DX56
0.40 - 0.45	1520	1520	-	-	-
0.45 - 0.50	1520	1520	1520	1520	1520
0.50 - 0.60	1520	1520	1520	1520	1520
0.60 - 0.65	1550	1550	1550	1550	1550
0.65 - 0.70	1550	1550	1550	1550	1550
0.70 - 0.90	1550	1550	1550	1550	1550
0.90 - 1.20	1550	1550	1550	1550	1550
1.20 - 2.00	1550	1550	1550	1550	-

The minimum width is 750 mm.

Thickness range 2.00 - 2.50 mm is available on request.