Thickness

The tolerances for thickness comply with standard EN 10143, 2006.

Tolerances closer than Special tolerances (S) are possible after consultation.

The following tolerances apply to the grades with a minimum value for the yield strength lower than 260 N/mm².

Dimensions in mm:

		Normal tolerances for a			Special tolerances (S) for a
Nominal Thickness		nominal width of 1 2)			nominal width of 1 2)
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.04	± 0.05	-	± 0.030	± 0.035	-
> 0.40	≤ 0.60	± 0.04	± 0.05	± 0.06	± 0.035	± 0.040	± 0.045
> 0.60	≤ 0.80	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.80	≤ 1.00	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 1.00	≤ 1.20	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.20	≤ 1.60	± 0.10	± 0.11	± 0.12	± 0.060	± 0.070	± 0.080
> 1.60	≤ 2.00	± 0.12	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 2.00	≤ 2.50	± 0.14	± 0.15	± 0.16	± 0.090	± 0.100	± 0.110
> 2.50	≤ 3.00	± 0.17	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130

¹⁾ Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed over a length of

    15 metres.
²⁾ For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02 mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength

260 N/mm² ≤ R_p0,2 < 360 N/mm² and for grades DX51D and S550GD. 

Dimensions in mm:

		Normal tolerances for a			Special tolerances (S) for a
Nominal Thickness		nominal width of 1 2)			nominal width of 1 2)
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.035	± 0.040	-
> 0.40	≤ 0.60	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.60	≤ 0.80	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.80	≤ 1.00	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.00	≤ 1.20	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.20	≤ 1.60	± 0.11	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 1.60	≤ 2.00	± 0.14	± 0.15	± 0.16	± 0.080	± 0.090	± 0.110
> 2.00	≤ 2.50	± 0.16	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130
> 2.50	≤ 3.00	± 0.19	± 0.20	± 0.20	± 0.130	± 0.140	± 0.150

¹⁾ Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed over a length of

   15 metres.
²⁾ For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02 mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength

360 N/mm² ≤ R_p0,2 ≤ 420 N/mm². 

Dimensions in mm:

		Normal tolerances for a			Special tolerances (S) for a
Nominal Thickness		nominal width of 1 2)			nominal width of 1 2 3)
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.040	± 0.045	-
> 0.40	≤ 0.60	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.60	≤ 0.80	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.80	≤ 1.00	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.00	≤ 1.20	± 0.10	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.20	≤ 1.60	± 0.13	± 0.14	± 0.16	± 0.080	± 0.090	± 0.110
> 1.60	≤ 2.00	± 0.16	± 0.17	± 0.19	± 0.090	± 0.110	± 0.120
> 2.00	≤ 2.50	± 0.18	± 0.20	± 0.21	± 0.120	± 0.130	± 0.140
> 2.50	≤ 3.00	± 0.22	± 0.22	± 0.23	± 0.140	± 0.150	± 0.160

¹⁾ Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed over a length of

    15 metres.
²⁾ For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02 mm.
3) Special tolerances (S) and tolerances closer than Special tolerances are possible after consultation.

The following tolerances apply to the steel grades with a minimum value for the yield strength

420 N/mm² < R_p0,2 ≤ 900 N/mm². 

Dimensions in mm:

		Normal tolerances for a			Special tolerances (S) for a
Nominal Thickness		nominal width of 1 2)			nominal width of 1 2 3)
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.06	± 0.07	-	± 0.045	± 0.050	-
> 0.40	≤ 0.60	± 0.06	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.60	≤ 0.80	± 0.07	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 0.80	≤ 1.00	± 0.09	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.00	≤ 1.20	± 0.11	± 0.13	± 0.14	± 0.080	± 0.090	± 0.110
> 1.20	≤ 1.60	± 0.15	± 0.16	± 0.18	± 0.090	± 0.110	± 0.120
> 1.60	≤ 2.00	± 0.18	± 0.19	± 0.21	± 0.110	± 0.120	± 0.140
> 2.00	≤ 2.50	± 0.21	± 0.22	± 0.24	± 0.140	± 0.150	± 0.170
> 2.50	≤ 3.00	± 0.24	± 0.25	± 0.26	± 0.170	± 0.180	± 0.190

1) Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed over a length of

    15 metres.
2) For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02 mm.

3) Special tolerances (S) and tolerances closer than Special tolerances are possible after consultation.

The tolerances for width comply with standard: EN 10143, 2006.

Tolerances closer than Special tolerances (S) are possible after consultation.

Dimensions in mm:

Nominal width		Normal tolerances		Special tolerances (S)
		lower	upper	lower	upper
≥ 750	≤ 1200	0	+5	0	+2
> 1200	≤ 1500	0	+6	0	+2
> 1500	≤ 1850	0	+7	0	+3

Tolerances on camber

The deviation from the edge camber does not exceed 5 mm for a length of 2 m.