• automotive industry: from essential construction parts to outer panels
• tubing
• domestic appliances
• steel furniture
• electrical goods
• domestic heating
• drums
• building

Metallic coated steel for forming complies with the following standards. 

European standard	National standards
	UK	Germany
EN 10327, 2004	BS 2989	DIN 17162-1
DX51D+Z/+ZF	Z1 + Z2	St 02 Z
DX52D+Z/+ZF	Z3	St 03 Z
DX53D+Z/+ZF	Z5	St 05 Z
DX54D+Z/+ZF	Z6 1)	St 06 Z
DX56D+Z/+ZF	-	St 07 Z 1)
DX57D+Z	-	-

¹⁾ Not in standard.

Metallic coated steel for forming has the following mechanical properties - these are measured transverse to the rolling direction, thickness t ≤ 3.0 mm:

	Re 1)	Rm	A80 min. 2)	r90 min.	n90 min.
Grade	N/mm²	N/mm²	%
DX51D+Z/+ZF	-	270-500	22	-	-
DX52D+Z/+ZF	140-300 3)	270-420	26	-	-
DX53D+Z/+ZF	140-260	270-380	30	-	-
DX54D+Z	120-220	260-350	36	1.6	0.18
DX54D+ZF	120-220	260-350	34	1.4	0.18
DX56D+Z	120-180	260-350	39	1.9 4)	0.21
DX56D+ZF	120-180	260-350	37	1.7 4 5)	0.20 5)
DX57D+Z	120-170	260-350	41	2.1 4)	0.22

¹⁾ The values of the yield strength are those of the 0.2% yield strength for products with no definite yield point, 

    the lower yield strength R_eL for the other products
²⁾ For a thickness t ≤ 0.7 mm the minimum elongation after fracture is decreased by 2%.
³⁾ This value only apllies to skin-passed products.
⁴⁾ For a thickness t > 1.5 mm the r₉₀ value is decreased by 0.2.
⁵⁾ For a thickness t ≤ 0.7 mm the r₉₀ value is decreased by 0.2 and the n₉₀ value is decreased by 0.01.

Tata Steel Strip Products IJmuiden complies with the following heat analysis with maximum values in weight percentages: 

	C	Mn	P	S	Al	N	Ti
Grade	Max.	Max.	Max.	Max.	Min.	Max.	Max.
DX51D+Z/+ZF	0.100	0.700	0.100	0.035	0.025	0.010	0.060
DX52D+Z/+ZF	0.070	0.300	0.030	0.035	0.025	0.005	0.005
DX53D+Z/+ZF	0.030	0.300	0.060	0.035	0.010	0.010	0.125
DX54D+Z/+ZF	0.010	0.300	0.030	0.035	0.010	0.006	0.125
DX56D+Z/+ZF	0.005	0.300	0.020	0.020	0.010	0.005	0.085
DX57D+Z	0.005	0.175	0.020	0.020	0.010	0.005	0.085

Galvanised steel for forming is available in the following dimensions in mm: 

	Max. width*
Thickness	MA, MB, MC
from-up to	DX51D	DX52D	DX53D	DX54D	DX56D	DX57D
0.35 - 0.40	1370	970	-	-	-	-
0.40 - 0.45	1520	1520	-	-	-	-
0.45 - 0.50	1520	1520	1520	1520	1520	-
0.50 - 0.55	1520	1520	1520	1520	1520	1450
0.55 - 0.60	1590	1590	1590	1590	1590	1590
0.60 - 0.65	1770	1770	1770	1770	1770	1780
0.65 - 0.70	1870	1870	1890	1890	1890	1890
0.70 - 0.75	1890	1890	1950	2020	2020	1930
0.75 - 0.80	1990	1990	1970	2020	2020	1900
0.80 - 0.90	2020	2020	2020	2020	2020	1820
0.90 - 1.00	2020	2020	2020	2020	2020	1770
1.00 - 1.10	2020	2020	2020	2020	2020	1620
1.10 - 1.20	2020	2020	2020	2020	2020	1490
1.20 - 1.35	2020	2020	1950	2020	2020	-
1.35 - 1.40	2020	2020	1930	2020	2020	-
1.40 - 1.50	2020	2020	1840	2020	2020	-
1.50 - 1.60	2020	2020	1740	1920	1920	-
1.60 - 1.75	2020	2020	1620	1770	1770	-
1.75 - 2.00	1970	1970	1500	1550	1550	-
2.00 - 2.25	1770	1770	-	-	-	-
2.25 - 2.40	1640	1640	1470	-	-	-
2.40 - 2.50	1570	1570	1370	-	-	-
2.50 - 2.60	1520	1520	1170	-	-	-
2.60 - 3.00	1520	1520	-	-	-	-

The minimum width is 750 mm.

Surface quality C with a thickness greater than 1.2 mm is only available after consultation.

* Widths over 1850 mm available after consultation.

Galvannealed steel for forming is available in the following dimensions in mm: 

Thickness	Max. width
from-up to	All grades
0.40 - 0.50	1350
0.50 - 0.60	1470
0.60 - 0.65	1730
0.65 - 0.70	1850
0.70 - 1.35	1850
1.35 - 1.40	1850
1.40 - 1.50	1850
1.50 - 1.60	1850
1.60 - 1.75	1680

The minimum width is 800 mm.